Woodwork Priming Guide: Prepare and Prime Wood, MDF and Skirting

Priming is the step that decides whether your skirting boards, doors and architraves look crisp for a decade or start flaking within two winters. Bare wood, MDF and old gloss each need a slightly different route: seal the knots, fill, prime, undercoat, then two thin topcoats. Do it in that order and the finish is smooth, even and durable. Our team at Tenen Ltd paints and decorates homes across West and Central London, and this guide sets out the routine we would want followed on any woodwork, so you can judge a finish with confidence, whether you do it yourself or hand it to us.
TL;DR
Bare softwood needs knotting on the knots, then primer, then undercoat, then topcoats. Skipping primer lets the wood drink the paint unevenly.
MDF needs a light sand with 120 to 180 grit, dust removal and a dedicated primer. Cut edges take extra coats.
Varnished or glossy woodwork needs cleaning and a light sand to create a key before primer goes on.
Fill holes and gaps, sand them flush and spot-prime the filler so it does not show through glossy topcoats.
Profile matters: ogee and torus skirting have grooves that collect paint, so use an angled brush and thin coats.
Table of Contents
Why primer matters on woodwork
Wood and MDF are porous. Paint applied straight onto them soaks in at different rates, which gives patchy sheen, raised grain and edges that look dull next to the faces. Primer seals the surface and gives the undercoat something consistent to grip. Zinsser UK says MDF should be primed because its porous surface absorbs paint unevenly without a primer coat.
On bare softwood there is a second job: stopping resin from knots bleeding through as yellow-brown stains. That is the reason knotting solution exists, and it is why a simple “one coat of primer” is not always enough.
Finally, primer protects the work you have already done. Every filled nail hole and sanded edge is a different texture from the surrounding wood. Primer evens those out before the visible coats go on.
Prepare the surface before any primer
Primer only sticks as well as the surface beneath it. Farrow & Ball advises that interior wood should be sound, clean, dry and free from dirt, grease and other contamination. In a London home that usually means:
Wash off grease and grime. Kitchen doors, hallway skirting and anything near a radiator collect a film of dust and cooking residue. Wipe down and let it dry fully.
Remove loose or flaking paint. Scrape back to a firm edge. Farrow & Ball recommends that peeled or blistered paint is sanded back to provide a key before a full coat of wood primer and undercoat.
Sand. Rawlins Paints suggests 120 to 150 grit abrasive to dull old gloss or satin and create a key for the new paint.
Fill. Dents, cracks and nail holes need filling and sanding flush (more on this below).
Remove dust. Vacuum, then wipe with a barely damp cloth. Dust trapped under primer shows up as grit in the finished gloss.
Older Victorian and Edwardian houses in Fulham, Chiswick or Kensington often carry many layers of paint. If detail is clogged or old coats are cracking, the woodwork may need more than a light sand, and that is a good point to ask a professional to look at it.
How to prime bare wood
New or stripped softwood, such as pine skirting or a replacement door, follows a set sequence. Wickes’ interior woodwork guide recommends two coats of knotting solution on knots, then primer, then undercoat. Here is how it works in practice.
Step 1: Knot the knots
Brush shellac-based knotting solution over every knot and any resinous patches, working just past the edge of each. Allow it to dry between coats as the tin directs. This is the only reliable way to stop resin staining the topcoat.

Step 2: Prime every face and edge
Use a wood primer or a combined primer and undercoat, applied by brush so it works into the grain. Pay particular attention to end grain, the cut ends of boards, which absorb the most. Farrow & Ball recommends a full coat of Wood Primer & Undercoat on bare wood after light sanding. Dulux Trade’s primer FAQ suggests, for new pine skirting, two coats of its quick-dry wood primer undercoat followed by one coat of high gloss. Always follow the instructions for the product you choose, because coat counts and drying times differ.
Step 3: Fill, then spot-prime
Once the primer is dry, small defects become visible. Fill them, sand flush and touch in with primer so the filler does not absorb topcoat differently.
Step 4: Sand lightly and undercoat
A very light pass with fine paper removes raised grain that primer always lifts. Wipe off the dust. Farrow & Ball asks for a minimum of four hours between coats on its system. Check the drying time of your own paint, and allow longer in cold or damp conditions.
Step 5: Two thin topcoats
Two thin coats beat one thick one. Lightly sand and dust between them. For the last coat, lay off in one direction, following the grain, with a light, unhurried stroke.
Priming MDF and getting clean edges
MDF is the standard material for modern skirting, architraves, built-in shelving and many kitchen and wardrobe fronts. It paints beautifully when prepared properly and badly when it is not. The faces are dense and smooth, but the cut edges are rough and thirsty.

Homebuilding’s 2026 guide says MDF faces can be lightly sanded with 120 to 180 grit, and that cut edges need extra preparation. It also notes that sanding creates a lot of dust, so a face mask is sensible. Zinsser UK recommends sanding with 120-grit paper, filling defects, removing dust, then priming overall with a full coat of its Bulls Eye 1-2-3 or B-I-N AQUA.
The practical rules:
Use a primer made for MDF or a stain-blocking water-based primer. Going straight to emulsion can swell the fibres and leave a rough, furry surface, as Homebuilding explains.
Plan on at least two primer coats. Homebuilding says two are typically needed, and cut edges may need a third.
Seal every edge, including the back and any routed or cut sections, before the board goes on the wall. It is far easier to do this at a trestle than on your knees in a hallway.
Sand lightly between coats and keep the dust under control.
If you are painting MDF kitchen doors or fitted cabinetry, spraying often gives the smoothest result. Our guide to spray painting interiors covers the preparation involved.
Painted, glossy or varnished wood
Most woodwork in an existing London home is already painted, so you rarely start from bare timber.
Sound existing paint. Clean it, sand lightly to dull the gloss, and dust off. Crown says lightly sanding and priming previously painted boards helps achieve the best finish, and that an undercoat improves the result particularly when going from a dark colour to a light one.
Varnished or stained wood. Varnish is slick, so paint has nothing to hold on to. Degrease it, sand it all over to create a key, remove the dust, then use an adhesion primer designed for glossy or varnished surfaces before undercoat and topcoats. Check the primer label states it suits varnished timber. If the varnish is peeling or the wood beneath is damaged, strip back the affected areas first.
Previously painted but flaking. Scrape and sand back to a sound edge, spot-prime the bare patches, then apply a full coat of primer-undercoat across the whole surface so the repair does not show.
Should you fill before or after priming?
The tidy answer is both, in stages. Fill obvious gaps and holes in the prepared surface, sand flush, then prime. After priming, small imperfections show up under the even colour, so a second light fill and spot-prime brings them level. Resene’s guidance notes that holes and voids in timber joinery can be spot-primed before filling and then reprimed after filling and sanding.
Use a flexible interior wood filler for cracks, holes and open joints, as Farrow & Ball recommends. Flexible filler copes better with the small seasonal movement of wood at joints. For the gap between the top of the skirting and the wall, a decorator’s flexible caulk, applied after priming, gives the crisp line that makes a room look finished.
Gloss level matters here too. Resene notes that higher-gloss finishes show imperfections such as filled nail holes more than lower-gloss ones. If your boards are not perfectly smooth, satinwood or eggshell is more forgiving than high gloss. Our guide to paint finish types compares them.
Skirting board profiles and what they mean for painting
The profile is the shape of the board’s top edge, and it affects both the look of the room and how you paint it. These are the profiles you will meet most often in UK homes:
Profile | Shape | Typical home | Painting note |
Ogee | S-shaped curve, concave then convex | Period and traditional homes | Curves hold paint, so use thin coats and check for runs |
Torus | Rounded, half-round top, often with a small step | Victorian and Edwardian terraces | Easy to brush, but the step line needs a neat cut-in |
Chamfered | Single flat angled cut on the top edge | Contemporary and 1930s to 1960s homes | Straightforward, the flat angle takes a small roller well |
Bullnose | Softly rounded top, no step | Modern renovations | Smooth and quick, edges need sealing if MDF |
Square or pencil round | Plain, near-flat face | Minimalist, new-build interiors | Shows every flaw, so preparation and gloss choice matter |
Skirting also comes in different heights. Taller boards of 150mm or more suit the high ceilings of many West London period properties, while shorter ones sit well in modern flats. In a refurbishment, matching a profile to the house’s period is one of the quiet details that makes the whole room feel right.
For painting, Rawlins Paints recommends an angled brush for top edges and corners, and says a small roller may suit long, flat sections if the profile allows. On ogee and torus, work the brush into the curve first, then lay off along the length.
How to paint skirting boards from start to finish
Once the woodwork is primed and undercoated, the visible coats are where care shows.
Choose the order. Crown says to paint skirting last when decorating a whole room, except when wallpapering, when the skirting goes first.
Mask the floor and wall edge. Use a low-tack decorator’s tape, or a paint shield if you prefer. Where the floor is new, protect it fully.
Cut in. Crown’s guide suggests cutting in at a 45-degree angle with long, smooth strokes, then painting the rest with a brush or small roller.
Sand and dust between coats. A light touch with fine paper and a wipe makes the second coat glide on.
Remove tape while the paint is still wet. Crown recommends this, and it avoids pulling off a dried edge.
A good brush is a real advantage on woodwork. Choose a quality angled brush, load it moderately and keep a wet edge. Our notes on painting and decorating tips cover more of this, and our guide to paint brands for London homes helps you pick products that suit the job.
Doors: a few tips that make the difference
Doors are skirting’s bigger cousin, and the same routine applies. Remove the handles and hinges where possible rather than masking them, and lay the door flat if you can, because flat painting avoids runs. Paint panels first, then the horizontal rails, then the vertical stiles, finishing with the edges. Seal the top and bottom edges of any door that is hung, since these are the surfaces most likely to take on damp.
Common mistakes and how to avoid them
No primer on bare wood. The topcoat goes patchy and may stain from knots.
Skipping the sand on old gloss. The paint looks fine for a few weeks, then peels away in sheets.
Painting damp wood or in cold rooms. Moisture trapped beneath primer causes blistering. Let the surface dry fully and allow longer between coats in winter.
Thick coats. They sag in curves and take far longer to cure. Two thin coats always look better.
Leaving dust. Every speck under the final coat is magnified by gloss.
Forgetting the order. Painting skirting before the walls means wall roller splashes land on fresh gloss.
If the woodwork sits in a bathroom or kitchen, damp and steam make preparation and product choice even more important, and it is worth planning the painting as part of the refit. We cover this in our kitchen renovation workflow.
Our perspective
Good woodwork painting is 80 per cent preparation. When we walk into a West London home, the first thing we look at is the skirting, the doors and the architraves, because they frame every room and they show everything. A sharp, even finish on those details lifts a whole refurbishment. That is why our painting and decorating is carried out in-house, under director oversight, rather than passed down a chain of subcontractors. The person who sands, fills and primes is part of the same team that finishes the room, so the standard stays consistent from first coat to last. Each project is priced as an itemised quotation after a site survey, so you know what the woodwork preparation includes before work begins. Our advice is simple: give primer and undercoat the time they need, keep coats thin, and treat every edge. That is how a room looks as good in five years as it does on the day we hand it back. Mateja
When to hand it to a professional
A single door or a short run of skirting is a reasonable weekend job. A whole house is different: dozens of boards, many doors, several drying cycles and the logistics of living around wet paint. Painting is also best coordinated with other trades, since skirting is fitted after plastering and floors, and painted after the dust has settled.
If you are planning a larger project, such as a kitchen, a bathroom, a loft conversion or a full refurbishment, woodwork painting belongs in the programme from the start. Tenen Ltd offers painting and decorating alongside property refurbishment for homeowners across West and Central London, with in-house project management and fixed, itemised quotes. If you would like a site visit to look at your woodwork, you can get in touch through tenenltd.co.uk.
FAQ
Do I need to prime bare wood before painting?
Yes. Primer seals the grain so paint dries evenly, and on softwood it works with knotting solution to stop resin staining the finish. Follow it with undercoat and two thin topcoats for the best result.
Can I use normal emulsion straight onto MDF?
It is not recommended. Homebuilding says going straight to emulsion can swell MDF fibres, so prime first with a suitable primer, and give cut edges an extra coat.
Can you prime over varnished wood?
Yes, once the varnish is clean, sound and sanded to a light key. Use a primer designed to bond to glossy or varnished surfaces, then undercoat and topcoats. Peeling varnish should be removed first.
Should I fill holes before or after priming?
Both, in stages. Fill the obvious defects, sand flush and prime, then fill any small flaws the primer reveals and spot-prime them. This stops filled areas showing through the topcoat.
Which should I paint first, skirting boards or walls?
Crown says to paint the skirting last when decorating a whole room, unless you are wallpapering, in which case the skirting goes first.
Sources
Recommended

Comments